Article Number: 000123995
Summary: Learn how to setup, use and troubleshoot Dell Thunderbolt Dock TB16. Find information about drivers, setting up multiple monitors and troubleshooting steps to resolve common issues.
- Article Content
- Article Properties
- Rate This Article
Article Content
Symptoms
Dell Thunderbolt Dock TB16 links all your electronic devices to your laptop PC using a single Thunderbolt 3 (Type-C) cable. When you connect the laptop to the docking station, you can gain access to all your peripherals such as the mouse, keyboard, stereo speakers, external hard drive, and large-screen displays without having to plug each device into the laptop.
NOTE: Dell Thunderbolt Dock TB16 only supports Thunderbolt 3 technology. Older versions of Thunderbolt are not supported.
For help with specifications, setup, connecting an external monitor, troubleshooting common issues, etc. refer to an expanding section below.
Cause
Specifications
Thunderbolt 3 (USB Type-C) |
|
|
|
|
|
System Requirements
The Dell Thunderbolt Dock - TB16 is designed for the following PCs with Thunderbolt 3 USB Type-C port:
Latitude | Precision Mobile | XPS Portable |
Latitude 12 5290 2-in-1 w/Tbt | Precision 15 3520 | XPS 13 2-in-1 7390 2-in-1 |
Latitude 13 5300 2-in-1 w/Tbt | Precision 15 3530 | XPS 13 9300 |
Latitude 13 5300 w/Tbt 3 | Precision 15 3540 | XPS 15 7590 |
Latitude 14 5400 w/Tbt 3 | Precision 15 3541 | XPS 13 9360 |
Latitude 14 5401 | Precision 15 5520 | XPS 13 9360 |
Latitude 14 5480 w/Tbt 3 | Precision 15 5530 | XPS 13 9365 |
Latitude 14 5491 w/Tbt 3 | Precision 15 5530 2-in-1 | XPS 13 9370 |
Latitude 15 5500 w/Tbt 3 | Precision 15 5540 | XPS 13 9380 |
Latitude 15 5501 | Precision 15 7520 | XPS 15 9560 |
Latitude 15 5580 w/Tbt 3 | Precision 15 7530* | XPS 15 9570 |
Latitude 15 5591 w/Tbt 3 | Precision 15 7540* | XPS 15 9575 |
Latitude 12 7200 2-in-1 | Precision 17 7720 | |
Latitude 12 7280 w/Tbt 3 | Precision 17 7730* | |
Latitude 12 7285 | Precision 17 7740* | |
Latitude 12 7290 w/Tbt 3 | *System requires the system's AC Adapter to supplement the Type-C connection to adequately power the system. | |
Latitude 13 7300 | ||
Latitude 13 7380 w/Tbt 3 | ||
Latitude 13 7390 2-in-1 w/Tbt 3 | ||
Latitude 13 7390 w/Tbt 3 | ||
Latitude 14 7400 | ||
Latitude 14 7400 2-in-1 | ||
Latitude 14 7480 w/Tbt 3 | ||
Latitude 14 7490 w/Tbt 3 | ||
NOTE: w/Tbt 3 indicates ordered with Thunderbolt 3 option. |
Ports and Features
Figure 1: Dell Thunderbolt Dock TB16 Ports
1. | HDMI |
2. | VGA |
3. | mini-DisplayPort (mDP) |
4. | DisplayPort (DP) |
5. | RJ45 Gigabit Ethernet |
6. | USB 2.0 (2 ports) |
7. | USB 3.0 |
8. | Thunderbolt 3 (USB Type-C) |
9. | 3.5 mm Speaker-out |
10. | 7.4 mm DC-in power |
11. | Dell Docking station connector (Dell Proprietary connection to USB Type 3 port on PC) |
12. | Headset Jack |
13. | USB 3.0 w/PowerShare |
14. | USB 3.0 |
15. | Power Adapter LED |
16. | Dock Button |
17. | Kensington lock slot |
NOTE: The Dell Thunderbolt dock will not function on a device with Display Port over USB Type-C with the Thunderbolt cable.
Installing drivers
NOTE: You must update your PC’s BIOS and the Dell Docking Station drivers to the latest versions available at the Dell Support Website before using the docking station. Older BIOS versions and drivers could result in the docking station not being recognized by your PC or not functioning optimally.
To learn more about installing drivers for Dell Thunderbolt Dock TB16 docking station, refer to the Dell knowledge-base article Dell Thunderbolt Dock TB16 - Driver Installation Guide
Automated driver installation using Dell Update/Dell Command | Update
Dell highly recommends the following applications to automate the installation of BIOS, firmware, driver, and critical updates specific to your PC and docking station. These applications are available to download on Dell Support Website Driver & Downloads page. Pick your PC type from the list or enter the service tag of your PC to get the right version for your PC.
- The Dell Update application is supported on Dell XPS laptops and Dell Venue
NOTE: A TB16 dock connection to your PC is required in order for Dell Update to start software updates on your PC.
- The Dell Command | Update application is supported on Dell Precision, XPS, and Latitude laptops.
NOTE: The latest Dell Update and Dell Command | Update are not capable of updating the Intel HD Graphics Driver to the latest version. Navigate to the Dell Driver & Downloads Website by searching the service tag of your PC. Download and install the latest Intel HD Graphics Driver in "Video" section for your PC.
Dell Thunderbolt Dock TB16 Manual Driver installation
Dell recommends installing the following BIOS, firmware, and drivers step by step in the prescribed order to ensure optimal performance.
NOTE: Administrative rights to the PC are required for Flashing the BIOS and installation of Thunderbolt driver/firmware.
Search for your PC model name under Select a Product selection, or enter the service tag of your PC to locate Drivers & Downloads page on the Dell support website. Change the Operating PC to view all available updates for your PC.
- Flash the latest Basic Input/Output System (BIOS) for the PC. This is available in the "BIOS" section
- Install the latest Intel Thunderbolt Controller Driver for the PC. This is available in the "Chipset" section
- Install the latest Intel Thunderbolt 3 Firmware Update for the PC. This is available in the "Chipset" section
- Install the latest Intel HD Graphics Driver for the PC. This is available in the "Video" section
- Install the latest ASMedia USB 3.0 Extended Host Controller Driver for Dell Thunderbolt Dock. This is available in the "Docks & Stands" section
- Install the latest RealTek USB GBE Ethernet Controller Driver for Dell Thunderbolt Dock and Dell Dock. This is available in the "Docks & Stands" section
- Install the latest RealTek USB Audio Driver for Dell Thunderbolt Dock and Dell Dock. This is available in the "Docks & Stands" section
- Restart the PC
- After the software update process completes, connect the AC adapter to the TB16 dock first and then attach the Thunderbolt 3 (USB Type-C) cable to the PC before using the docking station
Setting up an External Monitor
Microsoft Windows operating system includes the VGA graphics drivers only. For optimum graphics performance, it is recommended that Dell graphics drivers applicable for your PC be installed from Dell Drivers & Downloads website under the "Video" section.
NOTES:
- For NVIDIA Discrete Graphics solutions on the Latitude E-Family and Mobile Dell Precision PCs:
- First, install the Intel Media Adapter Graphics Driver applicable to your PC.
- Second, install the NVIDIA Discrete Graphics Driver applicable to your PC.
- For AMD Discrete Graphics solutions on the Latitude E-Family and Mobile Dell Precision PCs:
- First, install the Intel Media Adapter Graphics driver applicable to your PC.
- Second, install the AMD Discrete Graphics driver applicable to your PC.
Before connecting the docking station to your PC and connecting a monitor and other external devices, ensure to install all the required drivers.
Connect the monitor to the docking station using the VGA, HDMI, DisplayPort, mini-DisplayPort or USB-C cable provided with the monitor. The docking station supports up to 4 monitors that are connected simultaneously. Refer to the Display Resolution Table below for more details about the supported resolution when connecting multiple monitors to the docking station.
To learn more about setting up and troubleshooting issues with multiple monitor setups, refer to these Dell knowledge-base articles How to Set up Multiple Monitors or How to Troubleshoot Multiple Monitor Issues
Display resolution table
|
|
NOTE: DP port at 60 Hz is supported, but mDP +HDMI are limited to 30 Hz for 4k | NOTE: **Discrete only mode or "Special Graphics Mode".
|
NOTE: Resolution support is also dependent on the maximum resolution that is supported by the monitor.
NOTE: If higher resolution monitors are used, the Intel Graphics driver makes a judgment that is based on monitor specifications and display configurations. Some resolutions may not be supported and removed from the Intel Graphics Media Control Panel.
NOTES:
** Configuration that is supported with AMD and Nvidia in discrete-only mode or special-graphics mode. These modes are listed in the BIOS for the following PCs: Dell Precision 7510/7529/7710/7720 and requires disabling switchable graphics for discrete-only mode or enabling special-graphics mode when Switchable is enabled. If the PC does not have these options in the BIOS, then 4 monitors are NOT supported.
The 5K resolution support is only available in either of these conditions:
With
discrete graphics mode only, or special graphics mode or,
*** Using the Thunderbolt 3 USB Type–C to a dual DisplayPort adapter.
Troubleshooting
No video on the monitors that are attached to the High Definition Multimedia Interface (HDMI), mini-DisplayPort (mDP) port, or DisplayPort (DP) port on the docking station |
|
The video on the attached monitor is distorted or flickering. |
|
The video on the attached monitor is not displaying as an Extended Monitor. |
|
The audio connector is not functioning, no audio or there is a lag in the audio. |
|
The USB ports are not functioning on the docking station. |
|
The HDCP content is not displayed on the attached monitor. |
|
The LAN port is not functioning. |
|
Cable LED is not ON after it is connected to your host. |
|
USB port has no function in a pre-OS environment. | If your BIOS has a USB or Thunderbolt Configuration page, please make sure the following options are checked:
|
PXE boot on dock does not function. | If your BIOS has an integrated NIC page, please select Enabled w/PXE. If your BIOS Setup on your PC has a USB or Thunderbolt Configuration page, please make sure the following options are checked:
|
USB Boot does not function. | If your BIOS has a USB or Thunderbolt Configuration page, please make sure the following options are checked:
|
AC Adapter is displayed as "Not Installed" in the Battery Information page of the Dell BIOS Setup when the Thunderbolt 3 (Type-C) cable is connected. |
|
Peripherals connected to the docking station do not work in a pre-OS environment. | Thunderbolt Boot Support is by default, disabled in BIOS Setup on your Dell PC. With such default setting the docking station and the peripherals that are connected to the docking station do not work in a pre-OS environment. If the BIOS Setup on your PC has a USB or Thunderbolt Configuration page, check the following options to enable docking station function in a pre-OS environment:
|
Alert message "You have attached an undersized power adapter to your system" is displayed when the docking station is connected to your PC. |
|
Troubleshooting multiple monitor issues |
|
Frequently asked questions
What is the charging station feature?
The Dell Thunderbolt Dock TB16 can charge your mobile or power bank even without being connected to the PC. Make sure your dock is connected with external power. The dock fan rotates automatically if the dock gets too warm. This is normal working condition.
Latest Dell Thunderbolt Docking Station Product Available for Purchase and Support
Why am I asked to approve Thunderbolt Devices after the Windows logon and what should I do?
This is for Thunderbolt security. You are asked to approve a Thunderbolt device because the Thunderbolt Security level on your unit is set to "User Authorization" or "Secure Connect" in the BIOS Setup. You will not see this page if the Thunderbolt Security level on your PC is set to "No Security" or "DisplayPort Only". Also, if you checked "Enable Thunderbolt Boot Support" in the BIOS Setup and power-on the PC with TB16 attached, you will not see this page because the Security level is overridden to "No Security" in this case. When you are asked to approve a Thunderbolt device, you may select "Always Connect" if you do not have any security concerns to always allow the Thunderbolt device connection to your PC. Or you may select "Connect Only Once" or "Do Not Connect" if you do have concerns.
Why does it take a long time for the PC to recognize all the peripheral devices which are attached to the docking station?
Security is always Dell’s highest priority. We ship our PCs with "Security level - User Authorization" setting by default. This allows our customers to review the Thunderbolt security conditions of their PCs so they can make selections accordingly. However, this also means the Thunderbolt dock and the devices that are attached to it needs to pass Thunderbolt driver security permission checking to get it connected and initialized. This normally means that some extra time is needed before these devices can be accessed by users.
Why do the peripheral devices, which are connected to the dock station, become unresponsive after recovering from a power loss?
Our Thunderbolt dock is designed to operate in AC only, and it does not support PC power source back (powered by PC type-C port). A power loss event makes all devices on the dock fail to work. Even when you restore the AC power, the dock may still not function properly because the dock still needs to negotiate proper power contract with the PC Type-C port and establish a PC EC-to-dock-EC connection. A Type-C cable replug is needed to initiate the power contract negotiation and establish PC EC-to-dock-EC virtual I2C connection. As a result, after a power loss, the user needs to unplug type-C cable, replug in AC power, and then replug the USB-C cable to PC to restore dock back to normal condition.
The fan is not working after connecting to the PC
The fan is triggered by temperature. The dock fan will not rotate until the dock is hot enough to trigger a thermal threshold. Conversely, if your dock is not cool enough, the fan will not stop even when you disconnect the dock from the PC.
The dock does not work after high-speed fan noise
When you hear a loud fan noise, it is warning you that the dock is in some kind of a hot condition. For example, the vent in the dock may be blocked or the dock is working in a high working-temperature environment (> 35C). Eliminate these abnormal conditions from the dock. If you do not eliminate the abnormal condition, in a worst-case situation, the dock shuts down through the over-temperature protection mechanism. Once this happens, please unplug the Type-C cable from the PC and remove dock’s power. Then, plug in the dock power to recover the dock back online.
Why do I hear a loud fan noise from the docking station?
The dock fan is designed with two different rotate speeds. The dock works on low fan speed. If you put the dock in a heavy loading, or in high working-temperature environment, the dock fan may have a chance to work at a high speed. But, this is normal and the fan will work at a low/high speed depending on the work loading.
Resolution
NOTE: Currently, offers are only available for US, Canada, UK, and France PC customers. Server and Storage not applicable.
Article Properties
Affected Product
Dell Thunderbolt Dock TB16, Dell Venue 10 Pro 5056, Dell Venue 8 Pro 5855, Latitude 7275, Latitude E5270, Latitude E5470, Latitude E5570, Precision 3510, Precision 5510, Precision 7510, Precision 7710, XPS 12 9250, XPS 13 9350, XPS 15 9550
Last Published Date07 Jun 2021
Version10
Article TypeSolution